WIRES-X PC Software (Ver.2.010) – 5/2026

WIRES-X PC Software Update Information (Ver.2.010) – 5/2026

WIRES-X PC Software (Ver.2.010) – 5/2026

Unzip the downloaded zip file into any arbitrary location.

WIRES-X Remote Monitor Software (Ver.2.000) – 3/2026

Unzip the downloaded file 「wiresmon-x****en.zip」 into any arbitrary location.
Move the unzipped file to 「wiresmon-x」
Please refer how to use on the help file「WIRESMON-X.chm」

WIRES-X PC Software Update Information
Version 2.0xx (Supports portable digital node functionality)
This software is for PCs used by WIRES-X node stations.
Important
Before downloading the software, please read the “Important Notes” carefully.
Downloading this firmware will indicate your agreement with the contents of the “Important Notes”.
If you are installing this software on a computer that already has WIRES-X software installed, please refer to the
software installation instructions on page 3.
Main changes in Ver. 2.0xx

• Added support for WIRES-X operation using FTX-1
  The FTX-1 has built-in functionality equivalent to the HRI-200 and can be operated as a full-spec node.
• Router port forwarding settings are no longer required when operating as a node.
• When operating as a PDN, only information from connected stations can be displayed on the radio.
• Location information can now be changed via your PC.
• Other minor changes
  While port forwarding is no longer required in Ver. 2.0xx, there are some combinations of rooms that cannot con-
  nect due to incompatibility between the old and new software versions.
  Compatibility chart for old and new software versions
  Version of the connected room Version of my station
  Ver. 1.xxx Ver. 2.0xx
  Ver. 1.xxx 3 5 Cannot connect between the new version software to an
  old version room.
  Ver. 2.0xx
  New Version Exclusive
  Room 5 3
  Cannot connect between an older version software to a
  newer version room.
  Port forwarding is not required when using new version
  software to a new version room.
  Room compatible with
  older versions 3 3 Rooms compatible with older versions software require
  port forwarding setup.
  For owners who have already opened/operated a room, we ask that you consider migrating to room operation us-
  ing the “Old Version Compatible Room Function” with Ver. 2.0xx or later.
• If you already have an environment where a room is in operation (with an IPv4 Global IP and port forwarding en-
  abled), migration is possible with only a software version upgrade.
  Main changes in Ver. 2.010 (May 2026)
• Resolved an issue where Downlink audio could experience dropouts when multiple nodes in a Room initiated
  Uplink transmission at the same time.
• Fixed a bug where the Ver. 1.5 node would disconnect if there was an uplink from the FTX-1 node.
• Fixed an issue where QSL images were not transmitted correctly upon connection.
• Fixed a display corruption issue in the popup list of connected Nodes when a Ver. 1.5xx node connected to a
  Room with 129 or more node connections.
  Depending on the node/room version, there are combinations where the list of connected stations may not
  be displayed correctly (see table below). Therefore, please use Ver. 2.010 for both the node and room.
  Version of the
  connected room
  Version of my station
  Ver. 1.5xx Ver. 2.000 Ver. 2.010
  Ver. 2.000 5 3 5 Connections from versions 1.5xx and 2.010 will not
  display correctly.
  Ver. 2.010 3 5 3 Connections from Ver. 2.000 will not display correctly.
  2
  System Requirements
  OS: Microsoft Windows® 11
  Processor Clock Frequency: 2.0GHz or faster
  RAM that meets the OS system requirements (4GB or more recommended)
  Storage: 64GB or more free space (256GB or more SSD recommended)
  Display resolution: 1366 x 768 or higher 16-bit high color or higher (32-bit true color is recommended)
  USB port: Full-speed USB
  LAN port: 100BASE-TX/1000BASE-T or Wi-Fi: IEEE 802.11 b or higher Audio Interfaces*1
  *1 Sound function is also required when using the “Portable Digital Node Mode” or “Portable HRI
  Mode”. Furthermore, when communicating in “Direct Operation” in “Portable HRI Mode” using the
  FT5D, FT3D or FT2D the personal computer must have the “audio input from the microphone ter-
  minal pass to the speaker output” function.
  3.5Φ speaker terminal, 3.5Φ microphone terminal*2 (It is necessary only for Internet communication in “Portable
  HRI Mode”.)
  *2 In the case of a unique terminal such as a laptop, adapt it to a 3.5Φ speaker terminal and 3.5Φ microphone ter-
  minal with a commercially available conversion cable.
  Speaker: It is necessary only when communicating in “Direct Operation” in “Portable HRI Mode”.
  Internet Connection: High-speed lines such as fiber optic are recommended.
  Important Notes
  m All responsibility in using this firmware lies with the customer. We cannot be held responsible in any way for
  damages or losses which may be incurred by the customer as a result of using this firmware.
  m Copyrights and all other intellectual property rights for the firmware, as well as the manual, are the property of
  YAESU MUSEN CO., LTD.
  m The revision and modification of this firmware is prohibited. Redistribution, transfer, and resale of downloaded
  files are also prohibited.
  m Downloaded files are for personal use only.
  m If assistance is needed to perform the firmware upgrade, please consult with one of our sales sites or service
  centers

Visitas: 701