Firmware Download
| Download Type | Firmware |
|---|---|
| Model name | ID-52A PLUS, ID-52E PLUS |
| Version | Version 1.10 |
| Update | 2024/11/22 |
| Major changes | Changes from Version 1.00 – Supported the DV gateway function (Terminal mode/Access Point mode) on iOS devices with the newly released RS-MS3I. – Improved the importing repeater list. Supported importing repeater list while retaining the existing order. – Supported for the Memory Scope function in the Memory mode or the DR screen – Added an option for the Digital Repeater Set function. – Supported for microSDXC cards up to 256GB Formatting on the transceiver is required. – Shortened the time until the image was displayed when receiving the Share picture function in the DV mode. – Fixed a problem with a blank TX call sign in the DV mode transmission. – Fixed a problem in which the bit synchronization signal was shorter than expected when transmitting in the DV mode. |
| Note | The CS-52PLUS programming software used with this firmware can be downloaded here. To update the firmware 1. Download and unzip the firmware data (for example, 52PLUSE110.dat) and copy it into the “ID-52” folder that is on your microSD card. 2. Insert the microSD card with the firmware data into the transceiver. 3. Update the firmware. 3-1. Display the SD CARD screen in the Menu. 3-2. Select “Firmware Update” on the SD CARD screen to open the FIRMWARE UPDATE screen. 3-3. Push [▼] to scroll to the end of the screen to read all the precautions, after you read and agree with all the precautions, select [YES]. 3-4. The confirmation dialog recommends making a backup of the settings and memories, select [YES]. We recommend that you make a backup of them in this step, because all the settings and memories may be reset after updating the firmware. 3-5. After the backup file is made, and the firmware selection screen is displayed, select the firmware update data (for example, 52PLUSE110). 3-6. Please carefully read all the precautions, and when you want to execute it, select [Yes] to start the firmware update. 3-7. When the update is completed, the transceiver will automatically restart. If the setting data needs to be converted, it may take some time to restart. 4. If the settings and memories have been reset, load the settings and memories that have been backed up onto the microSD card. 4-1. Display the SD CARD screen in the Menu. 4-2. Select “Load Setting” on the SD CARD screen to open the LOAD SETTING screen. 4-3. Select the file name of the saved file. 4-4. Select “ALL,” and then the dialog “Keep ‘SKIP’ settings in the Repeater List?” is displayed, select [YES]. 4-5. The dialog “Load file?” is displayed, select [Yes]. 4-6. After the loading ends, “COMPLETED! Restart the ID-52.” is displayed, restart the transceiver. After updating the firmware, the Version Information in the OTHERS Set will be as follows. Main CPU: 1.10 Sub CPU: 1.00 DSP : 1.01 GPS: 13196 Bluetooth: 2.01 |
| File Size | 8.22MB |
| File Type | zip |
| Manual | manual download page |
| Document | Firmware Update Information |
https://www.icomjapan.com/support/firmware_driver/4242
Programming software Download
| Download Type | Programming software |
|---|---|
| Model name | CS-52PLUS |
| Version | Version 1.10 |
| Update | 2024/11/22 |
| Major changes | Changes from Version 1.00 – Compatible with ID-52A/E PLUS firmware version 1.10 Added an option for the Digital Repeater Set function – Improved the importing repeater list Supported importing repeater list while retaining the existing order |
| Note | -Before downloading, thoroughly read “CS-52PLUS INSTRUCTIONS” for installation details and requirements. – CS-52PLUS Version 1.10 can read the icf files you saved with the earlier software version. |
| File Size | 6.35MB |
| File Type | zip |
| Manual | manual download page |
https://www.icomjapan.com/support/firmware_driver/4243
Visitas: 31